- EPSON STYLUS R280 PRINTER NOT WORKING FOR MAC OS
- EPSON STYLUS R280 PRINTER NOT WORKING INSTALL
- EPSON STYLUS R280 PRINTER NOT WORKING DRIVER
EPSON STYLUS R280 PRINTER NOT WORKING INSTALL
Install a different size of cut sheet media or roll paper. The roll paper is out while printing is in progress.Īn A2 size cut sheet media or roll paper that does not support the borderless printing has been installed for borderless printing. Finally, set the paper lever to the secured position. Release the paper lever, and then remove the paper from the printer. Match the loaded paper with the paper type. The loaded paper does not match the paper type selected.
EPSON STYLUS R280 PRINTER NOT WORKING FOR MAC OS
For Mac OS X, see Cleaning the print head. For Windows, see Cleaning the print head. Remove the thick paper, and then move the paper lever to the secured position. To perform power cleaning, select YES and follow the messages on the LCD.Ĭleaning cannot be executed because thick paper is loaded. Replacement of the ink cartridge is nearly needed.Īlthough you can continue printing in INK LOW situation, the print quality may decline.Ī part used in the printer has nearly reached the end of its life. Replace the maintenance tank with a new one. See Lights.įor other messages not included in the following table, see Messages.Īn error may be occurring when you try to print patterns such as nozzle check or head alignment.Įxit the TEST PRINT menu first, and then solve the error displayed on the LCD. You can also check the lights on the control panel for errors. Many common printer problems and their solutions can be identified by the messages on the LCD.
Head cleaning, ink charging, or ink drying is in progressĭuring head cleaning, ink charging, or ink drying, CLEANING PLEASE WAIT, CHARGING INK, or INK DRYING appears on the LCD respectively. Troubleshooting on the Optional Auto Take-up Reel Unit Version 1.Paper feed or paper jam problems occur frequently If the supplied voltage and rating voltage do not match, do not plug the printer back in again, as damage may occur. If not, turn off the power and unplug the power cord immediately. Make sure the supplied voltage to the printer matches the rating voltage labeled on the printer. Make sure your outlet works and is not controlled by a wall switch or timer. Turn off the power and make sure the power cord is securely plugged into the printer. When the Operate light does not come on and mechanism initialization does not start (even when the Power button is pressed to turn on the printer), try the solutions listed for the problem. Note the error number "nnnnnnnn" and contact your dealer. Install the correct I/F card after turning off the power. Install or attach the maintenance tank again. Maintenance tank is not installed or not attached correctly. Ink cartridge(s) is (are) not installed or not attached correctly. Wrong ink cartridge(s) is (are) installed. Install ink cartridge(s) as indicated by the lights. Replace the ink cartridge(s) as indicated by the lights. When an error or status message appears again, clear and perform printing a test pattern again. Press the Pause button to exit the SelecType mode.
If an error occurs, or the ink lever is at the up position, you try to print a test pattern (nozzle check, status check, head alignment, or paper thickness pattern) from the SelecType settings.Īfter 3 seconds the message disappears. Push the paper lever down to remove the paper. Loaded paper is too thick for head cleaning. Start printing again from the beginning for best results. Set the paper lever to the secured position. Paper lever was released during the printing process or another operation. See Troubleshooting on the Optional Auto Take-up Reel Unit. Optional Auto Take-up Reel Unit is not operating correctly.Ĭheck whether the unit is operating correctly. Paper is set out of the horizontal cutting area.Ĭut the paper at the paper insertion slot, then reload paper. Remove then reload the paper so that the right and bottom edges are straight and in line with the rows of punch holes on the printer. Paper could not be reversed into the printing position. See Paper Feed or Paper Jam Problems Occur Frequently. Slippage occurred and paper was fed at an angle. When RELOAD PAPER is displayed, load paper.
See also Paper Feed or Paper Jam Problems Occur Frequently.Ĭut the paper manually, then remove the cut paper from the printer.
EPSON STYLUS R280 PRINTER NOT WORKING DRIVER
Make sure the paper source setting in the printer driver is the same as the control panel. The paper source setting in the printer driver is different from the control panel. If this message appears during a print job, reset the printer by pressing the Pause button for 3 seconds, then load paper and send the job again. Remove any printouts or paper remaining in the printer.